مراقب عام |
|
اشترك في: الاثنين إبريل 05, 2010 7:23 pm |
مشاركات: 13047 | مكان: المنصورة |
|
بوليرو كروشيه صيفى بالباترون بغرزة مخرمة روعه
بسم الله الرحمن الرحيم
Crochet bolero with lace pattern
Size: S/M - L/XL - XXL/XXXL Chest measurements: 84/94 - 100/110 - 120/130 cm
Materials: 200-250-300 g colour white
CROCHET HOOK SIZE 3 mm - or size needed to get 3 repetitions of pattern = width 10 cm.
CROCHET INFO: Replace first tr on every row with 3 ch.
PATTERN: See diagram A.1 - NOTE: The first row with dc is not in the repetition and is NOT repeated upwards. --------------------------------------------------------
BOLERO: Worked from mid back. First work one side and down to beg of sleeve, then work the other side and down to the other sleeve. Then sew the sleeve seams and work 1 flounce around the entire opening.
FIRST SIDE: Work 82-90-98 LOOSE ch with Cotton Viscose on hook size 3 mm – it is VERY important that this ch-row is not too tight. Work 1 dc in 2nd ch from hook, then work 1 dc in every ch the entire row = 81-89-97 dc. Continue pattern A.1 as follows: Diagram a over the first 9 dc, diagram b until 8 dc remain, then diagram c over these (= 10-11-12 repetitions in total on row). REMEMBER THE CROCHET TENSION! Repeat the 4 rows in diagram A.1 upwards until piece measures approx. 32-35-39 cm – finish after 4th row in diagram. Continue to work a finishing border as follows: ROW 1: 4 ch, 1 dc in first ch-loop, * 4 ch, 1 dc in next ch-loop, 4 ch, 1 dc in ch between the 4 tr, 4 ch, 1 dc in next ch-loop *, repeat from *-* the entire row, finish with 4 ch, 1 dc in last ch-loop, 3 ch and 1 dc in last tr, turn piece. ROW 2: Work as follows in every ch-loop: 1 dc + 1 picot (= 3 ch, 1 dc in first ch) + 1 dc. Cut and fasten the thread.
SECOND SIDE: Work along the other side of dc row made at the beg of first side (i.e. mid back) – beg with 1st row in A.1 and work as first side.
ASSEMBLY: Fold the bolero double across and sew tog from bottom of each sleeve and approx. 10 cm up in each side – sew edge to edge to avoid a chunky seam.
FLOUNCE AROUND OPENING: Work around the entire opening as follows (beg mid back): ROUND 1: 1 dc in first tr, * 3 ch, 1 dc in next tr *, repeat from *-* the entire round, finish with 3 ch and 1 sl st in first dc. ROUND 2: 2 ch, 1 dc in first ch-loop, * 4 ch, 1 dc in next ch-loop *, repeat from *-* the entire round, finish with 1 sl st in first dc. ROUND 3: 2 ch, 1 dc in first ch-loop, * 4 ch, 1 dc in next ch-loop *, repeat from *-* the entire round, finish with 1 sl st in first dc. ROUND 4: 2 ch, 1 dc in first ch-loop, * 5 ch, 1 dc in next ch-loop *, repeat from *-* the entire round, finish with 1 sl st in first dc. ROUND 5: 2 ch, 1 dc in first ch-loop, * 5 ch, 1 dc in next ch-loop *, repeat from *-* the entire round, finish with 1 sl st in first dc. ROUND 6: Work as follows in every ch-loop: 2 dc + 1 picot (= 3 ch, 1 dc in first ch) + 2 dc. Cut and fasten the thread.
|
|